Titan table saws are powerful and accurate machines that you can use for making high-quality and professional cuts. These affordable tools come with a 2-year manufacturer warranty and are loaded with all the functional and safety features.
However, electric and mechanical machines are prone to problems and damage, but the good news is that you can fix most of the titan saw problems without requiring professional help.
Many users ask about solutions to commonly occurring Titan table saw problems like motor problems, blade problems, excessive vibration, and bevel adjustment. Today, we will discuss the reasons behind these problems and how you can fix them.
Titan Table Saw Problems and Solutions
Problem # 1: Titan Table Saw Motor not running
The motor on your saw is responsible for driving the load. It generates the power required to spin the blade.
The motor is not getting voltage from the main supply line. Check the cable, plug, socket, and fuse to solve this problem. If you are using an extension cable with the saw, make sure that it is high quality and can support your tool’s voltage. Moreover, you must check which fuse you are using. Some tools require special circuit breakers.
Turn off the tool and unplug it. Check the motor casing, clean it using a vacuum and ensure that all vents are unblocked. If the problem persists, you will need to check motor switches, windings, and capacitor switches.
Voltage fluctuation has tripped the motor and triggered the under-voltage relay. If the tool gets the required voltage without any fluctuation, you need to replace the voltage relay.
The motor is overheated due to excessive load, wrong blade, or dust accumulation. Titan table saw motor problems can also happen due to using the wrong blade or exposing the saw to too much load. You need to ensure that the blade is properly sharpened and no teeth are damaged or broken. Moreover, you must also use an appropriate blade according to the material you cut. Using the wrong blade can lead to motor overheating.
The motor is overheated due to power switch problems. If the power switch gets blocked by dust accumulation or mechanical problems, it can cause the motor to get overheated.
Problem # 2: Blade makes Poor Cuts
Another common problem reported by Titan table saw users is poor cutting. This problem is directly related to the blade’s condition and indirectly to the motor. It can happen due to various reasons such as a dull or damaged blade, the wrong type of blade for cutting, a backward mounting blade, and the motor not producing the required power to run the blade at the optimum speed.
If the blade is not sharp or dirty, you need to remove the blade and sharpen every tooth to ensure smooth operation. You will have to replace the blade if it is damaged beyond repair.
You must use the right blade for the material you are cutting. The blade size and number of teeth on it must be according to the material you cut.
The blade may be mounted in the wrong direction. You will need to remove the blade and mount it in the right direction. The table saw blade always spins from the back to the front. You have to place the blade so that the cutting surface of the teeth is pushed into the wood and down. In other words, the sharp edges of the blade must face you.
Make sure you take all the safety precautions while troubleshooting the blade.
Problem # 3: Excessive Vibration
Titan table saws can vibrate excessively due to various reasons.
If the blade is out of order, it will make the whole tool vibrate excessively. The simple solution is to check if the blade’s arbor nut is loose or the blade has gone out of balance permanently. You can check this by removing the blade and placing it on a flat surface to see if it rests flat.
A damaged or warped blade can also lead to vibration. You cannot repair a damaged blade. You will have to replace the blade to remove this cause of vibration.
Vibration can also happen if the saw is not mounted correctly or if there are some loose parts, nuts, or bolts. This requires a thorough inspection of the tool, and you’ll have to identify each and every moving part to see which is not screwed properly and is causing problems.
If the saw is mounted and assembled correctly, then an uneven work surface can be the culprit behind excessive vibration. If you work out of a workshop or garage, check the surface below the saw. If you work on Jobsite, make sure you place the saw on a flat surface.
Problem # 4: Bevel Adjustment Hand Wheel doesn’t Spin
Over time the bevel adjustment handwheel and blade raising wheel can become hard to work with or get stuck. This problem is mostly related to the operator’s negligence and lack of maintenance.
The main reason behind this is dust accumulation and no oiling of the moving parts. It becomes hard to spin when sawdust accumulates at the gear and screw post on your Titan table saw.
You need to clean these parts thoroughly and ensure that dust doesn’t accumulate there. You can use a vacuum cleaner to remove the dust. Once all the moving parts are clean, use graphite to oil up these parts. Please don’t use grease as sawdust and debris readily stick to it.
Problem # 5: Angled Cuts Problems
Titan table saw may start to make inaccurate bevel cuts after some time because the positive stops inside the cabinet lose their adjustment. You need to adjust the positive stops in the cabinet.
Inaccurate bevel cuts can also happen due to the wrong blade setting. The bevel lever loses its accuracy over some time. The simple solution is to use a digital angle gauge to measure the angle.
Problem # 6: Kickback
Kickback is a common safety concern when using a table saw. It can happen due to a lot of problems. Some are related to safety components on a table saw, and some are linked to operational errors.
Kickback usually happens if the fence is not being used or the riving knife is not being used. It can also occur if the blade is dull and the workpiece is not held steadily while cutting.
Titan Table Saw User Manual
Want to read more about Titan Saw Problems and solutions.
Click here to download Titan Table Saw User Manual.
Final Words
So you see that most of the Titan table saw problems can be fixed at home without worrying too much. Titan is a British company. If you are buying a Titan table saw, keep in mind that you’ll have to deal with most problems yourself as they don’t have much presence in North America.